Teak board 40mm tree edge
Cutting

599,92  per m²

excl. Shipping
Area (m²)
Price per piece
Expected delivery by: May 29rd

Teak top with tree edge from BioMaderas

When cutting the high-quality teak top with a wane, you can already get the right size for the washbasin or kitchen worktop. When cutting the panel to size, however, it must be noted that the width of the panel can vary slightly due to the tree edge. In addition, with cuts under 80cm wide, you only get a tree edge on one side.

Wood pattern free

FSC teak top with tree edge from BioMaderas

Dimensions

Length 15cm to 200cm
Width 15cm to about 80cm
dimensional tolerance +/-2mm in length and width
also in standard sizes available
Size 40 mm
long side with teak tree edge
For cuts less than 80cm wide, the tree edge is only present on one side

Features

Species Teak (Tectona grandis)
application Solid wood with continuous wooden strips
Brand BioMaderas
Surface planed
Treatment natural
Certificate SVLK

Guides

instructions Data sheet as PDF
Item number: 6840-0000 Categories: , , , , , , Schlagwörter: , , ,

Processing instructions for solid wood panels

The solid slats for our solid wood panels are carefully selected and technically dried. They are glued together so that sapwood occurs predominantly on the B side. Wood core to wood core are therefore not glued alternately. We would like to give you a few important tips on how to handle solid wood panels. So that you can enjoy working with the natural material wood as much as we do!

Wooden top teak
Teak bathroom shelf

1. Appearance

Solid wood panels are a natural product. Our panels are sorted during production according to strict quality specifications. The special wood structure and the natural play of colors give each panel an individual character. They do not constitute a reason for complaint.

2. Acclimatization

The wooden panels must acclimatize for at least 48 hours in the room in which they are to be installed. To do this, lay the record flat and open the packaging. Protect the wooden panels from extreme changes in temperature and humidity. If the plate deforms, it must be turned over so that acclimatization can take place evenly on both sides. Bearing rails and, if necessary, weighing down the plate with a weight are also helpful.

Teak washbasin 40mm
Worktop raw oiled

3. Surface treatment

A surface treatment (e.g. oiling) must always be carried out to the same extent on both sides. We recommend that BioMaderas Olive oil for our solid wood panels.

4. preparation

Pre-drill holes for the necessary screws to reduce stress. Screws should be screwed at least 15 mm deep into the solid wood panel at least every 15 cm. The stabilizing strips should be selected in the profile so that they are statically effective and prevent the panel from warping. However, please note that this is a product made of solid wood, which swells and shrinks with fluctuations in humidity.

teak tree
Teak tree bark vanity

5. Assembly

Additional stabilizing strips should be attached to the underside to prevent the plate from deforming. Solid wood is a living material that expands and contracts with changes in temperature and humidity. A sufficiently wide expansion gap should therefore always be left open against all other non-living materials such as stone, steel, walls and pipes. It is best to cover this with a decorative strip. In addition, the solid wood panel should be ventilated from both sides. We advise against gluing the panel over the entire surface.

6. Nursing and Aging

After years of intensive use, the solid wood panel may show stains, scratches and streaks. To refresh, sand lightly with a grinder or fine sandpaper and re-oil if necessary. In this way, minor damage can also be treated.

Shipping Rate

Weight 32 kg
Species

wooden slats

continuous slats

Origin

Treatment

natural

Width

Length

Size

Product Type

Brand

Leaflet teak plates
Data sheet (PDF)

Technical data sheet and processing instructions for our teak wood panels as a PDF download.

Save cart
Share cart
Share cart