Furniture board teak 18mm
finger-jointed up to 120cm, FSC 100%

ab 15,00 

excl. Shipping
Expected delivery by: June 20rd

Teak furniture board 18mm finger-jointed up to 120cm from BioMaderas

Our 18mm thick wooden board FSC 100%-certified teak is used as a solid shelf, as a table top and for furniture construction. The wood is resistant to fungi and is often used in wet areas.

FSC shelf / furniture panel teak 18mm finger-jointed

Dimensions

Width 10cm to 100cm
Length 10cm to 120cm and 130cm to 240cm
Size 18 mm
Direction of grain in the direction of the page length

Features

Species Teak (Tectona grandis)
slats Solid wood finger-jointed
slat width 3cm to 7cm
gluing D4 (according to DIN EN 204, highest water resistance)
Surface sanded smooth
Drying technically dried
Origin Vietnam , FSC 100% certified

Guides

Online Wood panel advice
wood pattern free order
table support Eiermann table support
Recommended wood care BioMaderas Hard wax oil
Article number: 6719-0001 Categories: , , , , , Schlagwörter: , , ,

Processing instructions for solid wood panels

The solid slats for our solid wood panels are carefully selected and technically dried. They are glued together so that sapwood occurs predominantly on the B side. Wood core to wood core are therefore not glued alternately. We would like to give you a few important tips on how to handle solid wood panels. So that you can enjoy working with the natural material wood as much as we do!

Wooden top teak
Teak bathroom shelf

1. Appearance

Solid wood panels are a natural product. Our panels are sorted during production according to strict quality specifications. The special wood structure and the natural play of colors give each panel an individual character. They do not constitute a reason for complaint.

2. Acclimatization

The wooden panels must acclimatize for at least 48 hours in the room in which they are to be installed. To do this, lay the record flat and open the packaging. Protect the wooden panels from extreme changes in temperature and humidity. If the plate deforms, it must be turned over so that acclimatization can take place evenly on both sides. Bearing rails and, if necessary, weighing down the plate with a weight are also helpful.

Teak washbasin 40mm
Worktop raw oiled

3. Surface treatment

A surface treatment (e.g. oiling) must always be carried out to the same extent on both sides. We recommend that BioMaderas Olive oil for our solid wood panels.

4. preparation

Pre-drill holes for the necessary screws to reduce stress. Screws should be screwed at least 15 mm deep into the solid wood panel at least every 15 cm. The stabilizing strips should be selected in the profile so that they are statically effective and prevent the panel from warping. However, please note that this is a product made of solid wood, which swells and shrinks with fluctuations in humidity.

teak tree
Teak tree bark vanity

5. Assembly

Additional stabilizing strips should be attached to the underside to prevent the plate from deforming. Solid wood is a living material that expands and contracts with changes in temperature and humidity. A sufficiently wide expansion gap should therefore always be left open against all other non-living materials such as stone, steel, walls and pipes. It is best to cover this with a decorative strip. In addition, the solid wood panel should be ventilated from both sides. We advise against gluing the panel over the entire surface.

6. Nursing and Aging

After years of intensive use, the solid wood panel may show stains, scratches and streaks. To refresh, sand lightly with a grinder or fine sandpaper and re-oil if necessary. In this way, minor damage can also be treated.

Shipping costs

Weight n / A
Size n / A
Product Type

,

Species

wooden slats

finger-jointed slats

Origin

Size

Certificate

Surface

Quality

, ,

Length

, , , , , , , , , , , , , , , , , , , , , , ,

Width

, , , , , , , , , ,

Reviews

There are no reviews.

Be the first to review “Furniture Board Teak 18mm
finger-jointed up to 120cm, FSC 100%"

Save cart
Share cart
Share cart